| F1 |
Whirlpool |
Electronic control board failure or runaway temperature detected |
Disconnect power for 30 seconds to reset. If code persists, replace control board or temperature sensor |
| F2 |
Whirlpool |
Oven temperature too high - sensor detects temperature above safe limits |
Check oven temperature sensor resistance (should be ~1100 ohms at room temperature). Replace sensor or control board |
| F3 |
Whirlpool |
Open oven temperature sensor circuit - sensor is disconnected or faulty |
Check wiring connections to temperature sensor. Test sensor continuity. Replace if faulty |
| F4 |
Whirlpool |
Shorted oven temperature sensor circuit |
Inspect sensor wiring for damage or short circuits. Replace temperature sensor |
| F5 |
Whirlpool |
Control board failure - electronic control error |
Reset by unplugging for 5 minutes. If code returns, replace electronic control board |
| F6 |
Whirlpool |
Control board internal error or button stuck |
Check control panel for stuck buttons. Clean or replace control panel. May require control board replacement |
| F7 |
Whirlpool |
Stuck key or control panel communication error |
Inspect control panel for damage or stuck buttons. Replace control panel if necessary |
| F8 |
Whirlpool |
Oven door lock circuit error (on self-cleaning models) |
Check door lock mechanism and wiring. Ensure door latch moves freely. Replace lock assembly if faulty |
| F9 |
Whirlpool |
Oven door lock failure - door won't lock for self-clean cycle |
Inspect door latch mechanism for obstructions. Check lock motor wiring. Replace door lock assembly |
| F10 |
Whirlpool |
Cooling fan speed error - fan not operating correctly |
Check cooling fan for obstructions. Test fan motor. Replace cooling fan if faulty |
| F0 |
Ariston/Indesit |
Temperature sensor failure or disconnected sensor |
Check sensor connections. Test sensor resistance. Replace temperature sensor if readings are incorrect |
| F01 |
Ariston/Indesit |
Control board triac short circuit - heating element control failure |
Disconnect power and inspect control board for visible damage. Replace control board |
| F02 |
Ariston/Indesit |
Temperature sensor short circuit |
Check sensor wiring for damage. Replace temperature sensor |
| F03 |
Ariston/Indesit |
Oven not heating - relay stuck in closed position |
Replace control board as relay is integrated into the board |
| F04 |
Ariston/Indesit |
Temperature sensor open circuit or disconnected |
Check all sensor wire connections. Test sensor continuity. Replace if open circuit |
| F05 |
Ariston/Indesit |
Cooling fan failure - fan not turning |
Inspect fan for obstructions. Check fan motor connections. Replace cooling fan motor |
| F06 |
Ariston/Indesit |
Button permanently pressed on control panel |
Check control panel buttons for damage. Clean or replace control panel |
| F07 |
Ariston/Indesit |
Heating element relay stuck open - oven won't heat |
Replace control board (relay is part of board) |
| F08 |
Ariston/Indesit |
Cooling fan relay stuck closed |
Replace control board or check fan wiring for short circuit |
| F09 |
Ariston/Indesit |
Memory chip error on control board |
Reset by disconnecting power for 10 minutes. If persists, replace control board |
| F10 |
Ariston/Indesit |
Communication error between control boards |
Check wiring harness connections between boards. Replace damaged wiring or control boards |
| E1 |
Beko |
Temperature sensor malfunction - incorrect temperature readings |
Test sensor resistance (should be ~1080 ohms at 25°C). Replace sensor if faulty |
| E2 |
Beko |
Upper heating element temperature sensor error |
Check upper element sensor connections and resistance. Replace sensor |
| E3 |
Beko |
Door lock malfunction (on models with door lock) |
Inspect door lock mechanism. Check wiring. Replace door lock assembly |
| E4 |
Beko |
Cooling fan system error |
Check fan for obstructions and proper operation. Replace fan motor if not running |
| E5 |
Beko |
Control button stuck or control panel error |
Clean control panel. Check for stuck buttons. Replace control panel if necessary |
| E6 |
Beko |
Electronic control board failure |
Reset power. If error continues, replace main control board |
| E7 |
Beko |
Temperature sensor short circuit |
Inspect sensor wiring for damage. Replace temperature sensor |
| E01 |
Bosch |
Temperature sensor defective or poor connection |
Check sensor plug connections. Test sensor resistance. Replace if faulty |
| E011 |
Bosch |
Control panel button stuck in pressed position |
Clean control panel. Check for damaged buttons. Replace panel if needed |
| E031 |
Bosch |
Short circuit in temperature sensor |
Check sensor wiring for damage or pinching. Replace temperature sensor |
| E101 |
Bosch |
Oven overheating - temperature above safety threshold |
Check temperature sensor calibration. Inspect heating elements for faults. Replace sensor or control board |
| E115 |
Bosch |
Oven temperature too high during operation |
Allow oven to cool. Check for blocked ventilation. Replace temperature sensor if faulty |
| E131 |
Bosch |
Control board communication error |
Disconnect power for reset. Check wiring between control components. Replace control board if needed |
| ER1 |
Samsung |
Temperature sensor open circuit failure |
Check sensor wiring connections. Test sensor with multimeter. Replace sensor |
| ER2 |
Samsung |
Temperature sensor short circuit |
Inspect sensor wiring for damage. Replace temperature sensor |
| ER3 |
Samsung |
Oven overheating protection activated |
Allow oven to cool completely. Check temperature sensor. Reset by powering off for 10 minutes |
| ER4 |
Samsung |
Door lock error (self-cleaning models) |
Check door lock mechanism for obstructions. Test lock motor. Replace door lock assembly |
| ER5 |
Samsung |
Cooling fan error - fan not operating |
Inspect cooling fan for blockages. Test fan motor. Replace fan if not functioning |
| ER6 |
Samsung |
Control panel communication error |
Reset by disconnecting power. Check ribbon cable connections. Replace control panel or board |
| ER7 |
Samsung |
Button stuck on control panel |
Clean control panel thoroughly. Check for damaged buttons. Replace panel if necessary |
| C-21 |
LG |
Oven temperature sensor failure |
Check sensor connections and resistance (should be ~1080 ohms at room temp). Replace sensor |
| C-22 |
LG |
Oven overheating - temperature exceeded limits |
Turn off oven and allow cooling. Check ventilation. Replace temperature sensor or control board |
| C-23 |
LG |
Cooling fan system malfunction |
Check fan operation and connections. Remove obstructions. Replace cooling fan motor |
| C-31 |
LG |
Convection fan error (on convection models) |
Inspect convection fan for blockages. Test motor operation. Replace convection fan motor |
| C-43 |
LG |
Door lock failure - won't lock for self-clean |
Check door latch alignment. Inspect lock motor and wiring. Replace door lock mechanism |
| C-44 |
LG |
Door lock failure - won't unlock after self-clean |
Allow oven to cool completely. Manually release lock if possible. Replace door lock assembly |
| F- |
Electrolux |
Temperature probe failure or disconnected |
Check probe connections to control board. Test probe resistance. Replace if faulty |
| F1 |
Electrolux |
Electronic control board fault |
Reset by removing power for 5 minutes. Replace control board if error persists |
| F2 |
Electrolux |
Oven overheating detected |
Check temperature probe calibration. Inspect heating elements. Replace probe or control board |
| F3 |
Electrolux |
Oven temperature sensor open circuit |
Check all wiring connections. Test sensor continuity. Replace temperature sensor |
| F10 |
Electrolux |
Door lock circuit problem (self-clean models) |
Inspect door lock mechanism and wiring. Replace door lock motor assembly |
| F11 |
Electrolux |
Shorted keypad - control panel issue |
Clean control panel. Check for moisture damage. Replace control panel |
| F12 |
Electrolux |
Communication error between control components |
Check wiring harness connections. Reset power. Replace control board if needed |
| F30 |
Electrolux |
Temperature sensor reading too high |
Test sensor resistance. Check for short circuits in wiring. Replace sensor |
| F31 |
Electrolux |
Temperature sensor reading too low |
Check sensor connections. Test sensor resistance at room temperature. Replace if faulty |
| Er 01 |
Miele |
Temperature sensor defective |
Test sensor resistance (varies by model). Replace temperature sensor |
| Er 02 |
Miele |
Cooling fan malfunction |
Check fan for obstructions and proper operation. Replace cooling fan motor |
| Er 03 |
Miele |
Door lock failure |
Inspect door lock mechanism. Check electrical connections. Replace door lock unit |
| Er 04 |
Miele |
Control electronics fault |
Reset by disconnecting power. If persists, contact Miele service for control board replacement |
| Er 11 |
Miele |
Temperature too high - overheating protection |
Allow cooling. Check temperature sensor. Ensure proper ventilation. Replace sensor if needed |
| F or F- |
Siemens |
Temperature sensor error or disconnection |
Check sensor plug connection. Test sensor resistance. Replace sensor assembly |
| E011 |
Siemens |
Control button continuously activated |
Clean control panel. Check for stuck or damaged buttons. Replace control panel |
| E115 |
Siemens |
Oven overheating during operation |
Allow cooling period. Check temperature sensor accuracy. Replace sensor or control unit |
| E305 |
Siemens |
Communication fault between modules |
Check wiring between control boards. Reset power. Replace faulty control board |
| Er:01 |
Smeg |
NTC temperature sensor fault |
Check sensor connections and resistance. Replace NTC sensor |
| Er:02 |
Smeg |
Oven overheating protection activated |
Turn off and allow cooling. Check for ventilation blockages. Test temperature sensor |
| Er:03 |
Smeg |
Cooling fan not working correctly |
Inspect fan for obstructions. Test fan motor operation. Replace fan assembly |
| Er:04 |
Smeg |
Control panel or button malfunction |
Clean control interface. Check for stuck buttons. Replace control panel |
| F01 |
Hotpoint |
EEPROM memory error on control board |
Reset by powering off for 10 minutes. If persists, replace control board |
| F02 |
Hotpoint |
Temperature sensor resistance out of range |
Test sensor resistance. Check connections. Replace temperature sensor |
| F03 |
Hotpoint |
Oven overheating detected |
Allow oven to cool. Check temperature sensor calibration. Replace sensor |
| F04 |
Hotpoint |
Temperature sensor open circuit |
Check wiring connections. Test for breaks in wire. Replace sensor or wiring |
| F05 |
Hotpoint |
Door lock fault (pyrolytic cleaning models) |
Inspect door lock mechanism. Check motor operation. Replace lock assembly |
| F06 |
Hotpoint |
Control button continuously pressed |
Clean control panel. Inspect for damaged buttons. Replace control panel assembly |
| F10 |
Hotpoint |
Cooling fan fault |
Check fan operation. Remove blockages. Replace cooling fan motor if not spinning |
| PF |
GE/General Electric |
Power failure - oven experienced power interruption |
Simply press Cancel/Off button to clear. Reset clock if needed. No repair required |
| F1 |
GE |
Shorted keypad or control board failure |
Disconnect power for reset. Replace control panel or EOC (Electronic Oven Control) board |
| F2 |
GE |
Oven temperature too high |
Check oven sensor resistance (should be ~1100 ohms at 70°F). Replace sensor or EOC board |
| F3 |
GE |
Open oven sensor circuit |
Check sensor wire connections. Test sensor for open circuit. Replace sensor |
| F7 |
GE |
Stuck control panel button or touchpad failure |
Clean control panel. Check for stuck keys. Replace touchpad/control panel |
| F9 |
GE |
Door latch failure on self-cleaning models |
Inspect door latch assembly. Check motor operation. Replace door lock mechanism |
| Loc |
Various Brands |
Control lock activated - controls are locked |
Press and hold the control lock button (usually Lock or a padlock symbol) for 3-5 seconds to unlock |
| door |
Various Brands |
Door not properly closed or door switch fault |
Close door firmly. Check door alignment. Test door switch. Replace switch if faulty |
| bad Line |
Various Brands |
Incorrect electrical supply - voltage problem |
Check that cooker is connected to correct voltage (usually 240V). Contact electrician for wiring issues |
| F-H |
Various Brands |
Humidity sensor error (steam oven models) |
Check humidity sensor connections. Replace sensor if faulty. Applies to steam ovens only |
| Err |
Various Brands |
General error - various possible causes |
Note when error appears. Power cycle the unit. Check user manual for brand-specific meaning. Contact technician |